Please browse our selection here.
Home > Products > Development Board > Arduino > Arduino Shields
Sort byShowper page
    [Cytron] Easy MP3 Shield
    Here is another MP3 shield from Cytron, ezMP3 Shield is an Arduino compatible shield which is compatible with Genuino UNOCT-UNOCT-ARMGenuino Mega and possibly other pin compatible main boards. Cytron ezMP3 Shield offers high quality audio solution with the ability to decode and play MP3 audio files from microSD card.

    Cytron ezMP3 Shield has stackable side headers which allows more Arduino shield to be stacked on top of it. User can stack for example LCD Keypad Shield or Graphic LCD Shield and utilize it as control panel for ezMP3 Shield. It has the on-board mircoSD socket for microSD card with MP3 files. Cytron ezMP3 Shield has also on board 2 channel differential amplifier for direct drive of external loud speakers.
     
    On top of its many features, we like it because the MP3 decoder access the MP3 files directly on the microSD card, free up the Arduino proccessor for other task while MP3 file is being played. Awesome!
     
    This Cytron ezMP3 shield is different with Cytron MP3 shield, so the library is not compatible.

    Features:
    • 5V powered.
    • On board high quality MP3 decoder.
    • On board dual channel/Stereo 3W differential audio amplifier for external speaker
    • On board stereo 3.5mm audio jack socket for earphones.
    • On board microSD socket  for MP3 audio files storage.
    • A MicroSD status LED.
    • Interface from Arduino, UART, selectable to use soft serial.
    • Jumper selectors to select different  Control pins.
    • Stackable side headers.
    • Dimension : 69mm x 53mm
    RM68.90
    more info
    [Cytron] 2A Motor Driver Shield

    This is Cytron newly revised dual channel 2A motor shield. It uses L298P chip which allow control of two 5 - 26V DC brush motors with maximum of 2A current each channel. This shield can be directly stacked onto standard Arduino UNO, Duemilanove, LeonardoMega and also CIKU (PIC18F4550).

    We have added a few special features onto this shield. Motor power polarity protection, also fast test or manual control buttons for each channel of motor. Adding LSS05 (Auto-calibration line sensor) to Arduino will be easy as this shield comes with the socket for it.

    The speed control is achieved through conventional PWM which can be obtained from Arduino's PWM output pin 5 and 6. The enable/disable of motor driver is controlled by Arduino pin 4 and 7, this is labeled as Signed magnitude control. You have option to configure it to become Locked Anti-phase which uses PWM signal to decide direction, speed and also start/stop of motor. The control modes can be configured from jumpers and also program.

    The Motor shield can be powered directly from Arduino or from external power source (jumper to select). It is strongly encouraged to use external power supply to power the motor shield.

    RM44.50
    Out of stock
    more info
    [CYTRON]10A Motor Driver Shield (Arduino)

    Cytron 10A Motor Driver Shield (Arduino)"SHIELD-MD10" uses full solid state components which results in faster response time and eliminates the wear and tear of the mechanical relay. It has stackable side headers which allows for more Arduino shields to be stacked on top of it. Each shield comes with two mini jumpers for you to select different digital pin for PWM (speed) and DIR (direction), so you can actually stack more shield together.

    Features:
    • Bi-directional control for 1 brushed DC motor.
    • Support motor voltage ranges from 7V to 25V (Rev1.0), 7V to 30V (Rev2.0).
    • Maximum current up to 10A continuous and 15A peak (10 seconds).
    • 3.3V and 5V logic level input.
    • Solid state components provide faster response time and eliminate the wear and tear of mechanical relay.
    • Fully NMOS H-Bridge for better efficiency and no heat sink is required.
    • Speed control PWM frequency up to 10KHz.
    • Stackable I/O header pin.
    • Selectable digital pins for PWM and DIR.
    RM55.10
    more info
    Arduino Nano Expansion Module
    • Multi-Function Funduino Nano Shield Nano Sensor Expansion Board

      Description:

      This Nano Mult-Function expansion board is designed specially for Arduino Nano, solve the problem of wiring confusing when a variety of sensors connected.

      Lead out all digital IO port and analog IO port, each one with standard positive and negative power interface.

      Lead out the I2C interface of mainboard for convenient connection.

      Increasing the DC power supply interface. Nano USB interface supply current is actually only 50MA, to bring high-current devices, such as the steering, is obviously insufficient. So in the DC power connector provide external power supply to ensure the stability of equipment operation.

      Package included:

      1 x Nano shield

    RM10.00
    Stock available
    Add To Cartmore info
    ADK USB Host Shield for arduino
    • Google android adk function
    • Android phone
    • Android version 2.3.4
    • Compatible with Arduino Uno
    • Compatible with Arduino Mega 1280 and Arduino Mega 2560 (recommended)
    RM60.00
    Stock available
    Add To Cartmore info
    Sensor Shield V5.0 for arduino
    • Operating voltage:5 VDC
    • Input Voltage (limits): 6-20 VDC
    • Digital IO port: 13 ports prepared to digital modules or servos
    • Buckled Communication Port: Selectable between I2C and UART
    • Input Voltage: 7-12 VDC (recommended)
    • Buckled Analog Port: Handy, solid connection to 6
    • Analog inputs with VCC/GND
    • Analog IO Port: 2.54 grid male pin header connections
    RM15.00
    Stock available
    Add To Cartmore info
    L293D Motor Driver Shield for Arduino
    Chip:Wiznet W5100 Ethernet Chip
    Network (IP) stack capableTCP and UDP
    as Mega (1280/2560)
    Network (IP) stack capable:TCP and UDP
    Other feature:Micro SD card slot
    Chip:Wiznet W5100
    Supported Arduino board:Compatible with t:
    he Arduino Duemilanove (168 or 328)
    Ability:Can drive 4 DC motors or 2 stepper motors or 2 Servo
    pack size:8cm x 5cm x 2cm weight :36g
    RM25.00
    Stock available
    Add To Cartmore info
    w5100 Ethernet shield for arduino

    Arduino Wiznet Ethernet W5100 Shield

    This Ethernet board is a top quality product which works just the same as the official board. It contains the same chipset and so all of the examples using the Ethernet library work just the same. This board offers a substantial discount on the official board.

    Arduino Ethernet Shield With Wiznet W5100 Ethernet Chip
    Supports TF card up to 16GB
    Uses standard Arduino Ethernet drivers
    The Arduino Wiznet Ethernet W5100 Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W5100 ethernet chip providing a network (IP) stack capable of both TCP and UDP. The Arduino Ethernet Shield supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield.

    The on-board micro-SD card slot can be used to store files for serving over the network. It is compatible with the Arduino Uno and Mega (using the Ethernet library). You can access the on-board SD card slot using the SD library which is included in the current Arduino build.

    Arduino communicates with both the W5100 and SD card using the SPI bus (through the ICSP header). This is on digital pins 11, 12, and 13 on the Uno and pins 50, 51, and 52 on the Mega. On both boards, pin 10 is used to select the W5100 and pin 4 for the SD card. These pins cannot be used for general i/o. On the Mega, the hardware SS pin, 53, is not used to select either the W5100 or the SD card, but it must be kept as an output or the SPI interface won't work.

    Note that because the W5100 and SD card share the SPI bus, only one can be active at a time. If you are using both peripherals in your program, this should be taken care of by the corresponding libraries. If you're not using one of the peripherals in your program, however, you'll need to explicitly deselect it. To do this with the SD card, set pin 4 as an output and write a high to it. For the W5100, set digital pin 10 as a high output.

    RM30.00
    Stock available
    Add To Cartmore info
    [Cytron] PS2 Shield
    Features:
    • 5V powered, low current consumption.
    • Simple to use UART protocol
    • Vibrator motor on PS2 is controllable.
    • Wired and Wireless PS2 controller is supported.
    • PS2 Controller will automatically operate in analog mode.
    • A status LED
    • Jumper selector to select different UART Baud Rate (9600, 57600, 115200).
    • Jumper selectors to select different digital pin as UART TX and RX pin.
    • Dimension: 68mm x 53mm
    RM65.80
    more info
    [CYTRON] ESP8266 WiFi Shield
    RM52.90
    Stock available
    Add To Cartmore info
    Arduino Mega Sensor shield v2.0

    The Arduino MEGA has many more I/O pins (54 Digital pins and 16 Analog pins)than a standard Arduino. This shield also has connectors specifically for some external devices like an SD Card, Radio communications (Bluetooth and others). It also has an option to power the "V" pins on all the Digital I/O 3-pin groups from an external power supply instead of the Arduino +5V. This is good for large numbers of servos etc. The "Analog" 3-pin groups still use the Arduino +5V which is better from an electrical noise perspective.

    RM19.00
    Stock available
    Add To Cartmore info
    Arduino Mega prototype shield+breadboard

    Size : 20cm x 15cm x 16cm (7.87" x 5.91" x 6.30")

    RM19.00
    Stock available
    Add To Cartmore info
    ARDUINO UNO PROTOTYPE SHIELD + BREADBOARD

    This is a high quality Arduino Prototyping Shield clone that makes it easy for you to design custom circuits. You can solder parts to the prototyping area to create your project, or use the small included solderless breadboard to quickly test circuit ideas without having to solder. It's got extra connections for all of the Arduino I/O pins, and it's got space to mount through-hole and surface mount integrated circuits. It's a convenient way to make your custom circuit and Arduino into a single module.

    The Proto Shield bring the power from the Arduino standard 5V and GND pins to the two power bus rows placed between the Through Hole package footprint, which can be used for powering the DIP sockets, or for power and ground rows.

    RM14.50
    Stock available
    Add To Cartmore info